
Product Details
Overview
Stereo transmitter for use with Audio-Technica M2L and M2M Wireless In-ear Monitor Systems. Equipped with two XLR/¼" combo input connectors. Includes AC adapter (country dependent) and rack mount adapters.
The M2 Wireless In-Ear Monitor System is designed to make professional in-ear monitoring features accessible for performers who want to be free from the problems associated with floor wedges. The stereo monitor system offers Personal Mix Control, which gives each musician volume and mix control of two independent signals on stage, via easy-to-use controls on the M2R stereo body-pack receiver. The wireless UHF M2T Stereo Transmitter provides a choice of 100 selectable frequencies and is equipped with two XLR/¼” combo input connectors into which users can connect line-level inputs. While up to 10 complete M2 systems may be used on stage simultaneously, any number of M2R stereo receivers may be used on the same frequency with a single M2T stereo transmitter. These rugged systems are built to stand up to the inevitable bumps of life on the road, delivering clear, natural sound for touring and installed-sound uses.
Features
High-fidelity sound with clean, articulate mix allows you to hear yourself better at lower volume
100 selectable UHF channels
Up to 10 simultaneous systems per frequency band
Three receiver modes: Personal Mix, stereo, and mono
Personal Mix Control allows volume and mix control of two independent signals at the receiver
3.5 mm line-in jack connects to ambient microphone, click track & more
LED indicators provide easy-to-read level monitoring
XLR loop output (true pass-through) connects signal to mixing console, additional IEM system or recording device with no signal degradation
Adjustable squelch eliminates annoying static
Pilot tone protects against RF interference when the transmitter is turned off
Limiter (defeatable) helps protect your hearing from sudden peaks
Portable system is quick to load and set up
Reduces on-stage audio clutter for better overall mix & less feedback
Use any number of M2R Stereo Receivers (with Personal Mix Control) on the same frequency
Audio-Technica earphones with proprietary dynamic drivers offer full frequency response and outstanding isolation
Personal fit with 3 sizes of rubber eartips plus ear-conforming foam tips
Auxiliary input offers connection point for ambient microphone, click track, or other mic- or line-level input.
Specifications
OVERALL SYSTEM
Operating Frequencies
Band E: 790.000 to 822.000 MHz, 100 frequencies
Band F: 832.000 to 865.000 MHz, 100 frequencies
Band L: 575.000 to 608.000 MHz, 100 frequencies
Band M: 614.000 to 647.000 MHz, 100 frequencies DISCONTINUED IN NORTH AMERICA
Not all frequency bands available in all areas. Please check with local regulations.
Minimum Frequency Step
25 kHz
Modulation Mode
FM stereo
Maximum Deviation
±40 kHz
Dynamic Range
90 dB (typical), A-weighted
Total Harmonic Distortion
<1% at (1 kHz, ±20 kHz Deviation)
Operating Range
100 m (300'), typical
Open range environment with no interfering signals.
Operating Temperature Range
-5° C (23° F) to +50° C (122° F)
Battery performance may be reduced at very low temperatures.
Frequency Response
60 Hz to 13 kHz (+/- 3 dB)
Simultaneous Use
10 channels per band (maximum recommended)
For assistance with multi-band operation or other frequency coordination issues, please contact your local Audio-Technica customer service representative.
RECEIVER
Receiving System
Double conversion superheterodyne
RF Sensitivity
20 dBuV (at 60 dB S/N ratio, 50 ohms termination)
Headphone Output Connector
3.5 mm TRS stereo phone jack
Headphone Output Power
65 mW (at 32 ohms)
Antenna Input
SMA-type, 50 ohms
Aux Input Connector
3.5 mm TRS stereo phone jack
Batteries
2 x 1.5V AA (not included)
Battery Life
8 hours (alkaline)
Depending on battery type and use pattern
Dimensions
70.0 mm (2.76") W x
25.0 mm (0.98") D x
110.0 mm (4.33") H
Net Weight
110 g (3.9 oz), without batteries
Accessories Included
EP3 earphone; frequency sticker; flexible antenna
TRANSMITTER
RF Power Output
10 mW/30 mW (switchable internally), 50 ohms
Limited to 10 mW within 863 MHz to 865 MHz
Following national regulations
Spurious Emissions
Following federal and national regulations
Input Connections
XLRF-type/6.3 mm stereo (1/4") combination connector
Pin 1 and Sleeve: Ground
Pin 2 and Tip: Hot
Pin 3 and Ring: Cold
Maximum Input Level
XLRF-type/6.3 mm stereo, (1/4") balanced: +26 dBu
6.3 mm (1/4") mono, unbalanced: +26 dBu
Loop Output Connector
XLRM-type connector
Pin 1: Ground
Pin 2: Hot
Pin 3: Cold
Power Requirement
12-18V DC, 600 mA
Antenna
Attached whip
Dimensions
210.0 mm (8.30") W x
132.0 mm (5.20") D x
44.0 mm (1.70") H
Net Weight
870 g (30.7 oz), without accessories